PLASTIC AND EMBLEM ADHESIVE (08061) - A clear adhesive
for bonding a variety of plastics to metal and other materials.
Suitable for adhering rigid plastic interior trim, exterior
protective vinyl trim, and plastic or metal emblems.
SUPER WEATHERSTRIP ADHESIVE (8001) - A light colored,
fast drying, high strength, waterproof adhesive for bonding
all types of weatherstripping. Also bonds all types of gaskets
to metal. Resists oils, solvents, and greases.
SUPER TRIM ADHESIVE (8090) - A contact adhesive designed
for bonding vinyl tops, and headliners, where strength and
heat resistence are needed.
SUBORDINATE ADHESIVE (PC-2) - Bonds vinyl coated and
laminated fabrics, plastics, metals, woods and leather. Brushes
smoothly and quickly, fast drying, waterproof, versatile and
has a long shelf life.
BOND-CA (PT-08) - A very thin viscosity cyanoacrylate,
instant curing adhesive for vinyl, leather or tacking operations
on plastic and urethane bumper repairs. Used to cure Micro
Balloons.
FLEX-BOND (PT-32) - A thin viscosity cyanoacrylate
adhesive used for filling small gaps, retaining texture and
bonds to porous surfaces. Create texture by dabbing wet glue
with a piece of foam rubber, use accelerator, then sand with
320-400 grit sandpaper to lever the top of the grain. Not
recommended for large areas as cracking will occur on very
flexible surfaces.
FLEX GEL (PT-31 & PT-31C) - A medium viscosity
cyanoacrylate adhesive used for filling gaps, retaining texture
and bonds to porous surfaces. Provides the best flexibility
of all cyanoacrylate adhesives available. Comes in black or
clear.
BOND-A-GAP (PT-02) - This is a "non surface sensitive"
adhesive, which means it will bond to surfaces that are contaminated
with oils, silicones, and mold released agents. The medium
viscosity allows you time to position your components before
it cures.
SLO BOND (PT-20) - A thick viscosity cyanoacrylate
with gap filling qualities. It will have the slowest curing
time of all the adhesives except Power Gel.
POWER GEL (SPG) - The thickest viscosity cyanoacrylate
adhesive. Use where maximum filling or heavy texture is required.
Can also be used to fix vinyl in areas where flexibility is
not essential or for thin vinyl where heat can not be used.
For example, cracks in armrests, dashes, door panels or console
covers.
BOND KICKER (PT-15) - An accelerator for speeding
up the drying time for cyanoacrylate adhesives. It can be
applied by brush, sprayer or dropper. If you apply the kicker
before applying the glue you will have an instant setting
on vertical surfaces. By applying before and after will set
thick adhesive from both top and bottom producing catalytic
action.
BOND RELEASE (PT-16) - For those of us who have a
habit of getting glue on us and not knowing until we are stuck
on something, there is debonder. Squeeze a little on the surface
of bonded material and gently work in. Results should be immediate.
LIQUID VINYL (4909-16) - Clear flexible liquid vinyl
used with Dash Putty Powder. Also used for adhering vinyl
and leather.
Z-ENDS AND TUBES (PT-18) - Cone shaped ends for the
bottles of cyanoacrylate glues to put the glue right where
you want it. For those hard to reach areas these tubes will
fit right on the bottles and will dispense the glue in a fine
bead. Also contained in the kit are nylon tubes for super
fine beading.
SILICONE (SILI) - Heavy duty adhesive for attaching
dash caps and arm rest covers. This is a clear silicone that
bonds permanently.
T-10 REDUCER (T10) - This product is used to thin
down PC2 Subordinate adhesive. If there is too much adhesive
applied on a repair, wipe excess off immediately and if any
PC2 has hardened, it can be worked down with the T10 reducer.
Apply with a Q-tip and keep wiping until you reach the desired
level.